ISSN 2466-4677; e-ISSN 2466-4847
Journal Menu
Archive
Last Edition
Archive
Tensile Properties, Micro-computed Tomography Defect Analysis, and Milling Performance of As-Built and Heat-Treated CuCrZr Parts Fabricated by Laser Powder Bed Fusion
Authors:
Subba Reddy Mundla1
, Arungalai Vendan Subbiah2
,
C. P. Paul3
,
Arun Kumar Shettigar1
, Sudhakar C. Jambagi1
1Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal, India
2Department of Electronics and Communication Engineering, Dayananda Sagar University, Bangalore South, Karnataka, India
3Raja Ramana Centre for Advanced Technology, Indore, India
Received: 21 July 2026
Revised: 10 September 2026
Accepted: 17 September 2026
Published: 23 September 2026
Abstract:
Copper–chromium–zirconium (CuCrZr) is an age-hardenable copper alloy valued for its rare mix of high strength and thermal conductivity, making it a logical choice for heat sinks, divertor parts, and rocket-engine liners. Laser powder bed fusion (LPBF) can fabricate such parts with internal cooling channels that are difficult to machine conventionally; however, this process makes the alloy a bit softer and may eventually lead to the formation of internal pores or voids. This study focuses on how LPBF CuCrZr behaves, both mechanically and during milling, in the As-Built (AB) and heat-treated states. Vickers hardness rose from about 118 HV in the AB state to 152 HV after heat treatment. Tensile testing demonstrated the ultimate tensile strength improving from roughly 680–700 MPa to 780–820 MPa, a gain of about 15–18%, while total elongation remained at or above 95% for all heat- treated specimens. Micro-computed tomography (μCT) confirmed a dense build in both states, with relative density near 99% and no lack-of-fusion defects or cracking; only a few small, isolated gas pores were seen. In milling, the harder, heat-treated material required slightly higher cutting forces (CF) but produced a more stable cut and better surface finish, with the lowest 3D roughness at high cutting speed (CS) and low feed. Scanning Electron Microscopy (SEM), Energy-Dispersive Spectroscopy (EDS), and Atomic Force Microscopy (AFM) were used to characterize the microstructural, compositional, and surface-topographical changes, respectively, observed after heat treatment. Consequently, the heat treatment strengthens LPBF CuCrZr and improves surface finish without compromising the soundness or ductility.
Keywords:
CuCrZr, Laser powder bed fusion, Heat treatment, Milling, Surface roughness, Cutting forces, Tensile behaviour, Micro-computed tomography
References:
[1] J. Li, Z. Kuai, Z. Li, B. Liu, Y. Chen, S. Lu, Y. Nie, Z. Yang, Effects of process parameters on the relative density and properties of CuCrZr alloy produced by selective laser melting. Metals, 12(5), 2022: 701.
https://doi.org/10.3390/met12050701
[2] D. Cortis, E. Mancini, D. Orlandi, D. Pilone, M. Sasso, Additively manufactured CuCrZr alloy: Improvement of mechanical properties by heat treatment. Procedia Structural Integrity, 47, 2023: 908–914.
https://doi.org/10.1016/j.prostr.2023.07.021
[3] Z. Diao, F. Yang, R. Wang, Y. Zhang, L. Chen, T. Xiong, W. Yang, M. Rong, Effect of heat treatment on the microstructure and properties of CuCrZr alloy manufactured by wire arc additive manufacturing. Journal of Alloys and Compounds, 967, 2023: 171786.
https://doi.org/10.1016/j.jallcom.2023.171786
[4] T. Wegener, J. Koopmann, J. Richter, P. Krooß, T. Niendorf, CuCrZr processed by laser powder bed fusion — Processability and influence of heat treatment on electrical conductivity, microstructure and mechanical properties. Fatigue & Fracture of Engineering Materials & Structures, 44(9), 2021: 2570–2590.
https://doi.org/10.1111/ffe.13527
[5] T. Baffie, G. Roux, C. Flament, M. Soulier, M. Pellat, C. Salvan, C. De Vernon, Effect of powder batches and laser power on the microstructure and properties of As-Built and heat-treated laser powder bed fusion CuCrZr samples. World PM2022 Proceedings, 9–13 October 2022, Lyon, France.
https://doi.org/10.59499/WP225371437
[6] A.M. Khorasani, I. Gibson, A. Ghasemi, A. Ghaderi, Modelling of laser powder bed fusion process and analysing the effective parameters on surface characteristics of Ti-6Al-4V. International Journal of Mechanical Sciences, 168, 2020: 105299. https://doi.org/10.1016/j.ijmecsci.2019.105299
[7] D. Guillen, S. Wahlquist, A. Ali, Critical review of LPBF metal print defects detection: Roles of selective sensing technology. Applied Sciences, 14(15), 2024: 6718. https://doi.org/10.3390/app14156718
[8] F. Canillas, E. Leon-Gutierrez, M. Roldan, R. Hernandez, E. Urionabarrenetxea, E. Cardozo, L. Portoles, J.R. Blasco, N. Ordas, On the feasibility to obtain CuCrZr alloys with outstanding thermal and mechanical properties by additive manufacturing. Journal of Nuclear Materials, 601, 2024: 155304.
https://doi.org/10.1016/j.jnucmat.2024.155304
[9] K. Jahns, R. Bappert, P. Böhlke, U. Krupp, Additive manufacturing of CuCr1Zr by development of a gas atomization and laser powder bed fusion routine. The International Journal of Advanced Manufacturing Technology, 107(5), 2020: 2151–2161. https://doi.org/10.1007/s00170-020-04941-7
[10] H. von Lintel, E. Evsiutkina, C. Haase, U. Krupp, K. Jahns, Copper alloys for additive manufacturing: Laser powder bed fusion of CuCr1Zr by using a green QCW laser. European Journal of Materials, 3(1), 2023: 2115945. https://doi.org/10.1080/26889277.2022.2115945
[11] P. Guan, X. Chen, P. Liu, F. Sun, C. Zhu, H. Zhou, S. Fu, Z. Wu, Y. Zhu, Effect of selective laser melting process parameters and aging heat treatment on properties of CuCrZr alloy. Materials Research Express, 6(11), 2019: 1165c1. https://doi.org/10.1088/2053-1591/ab4e2f
[12] J. Skiba, M. Kulczyk, S. Przybysz-Gloc, M. Skorupska, J. Smalc-Koziorowska, M. Kobus, K. Nowak, Thermo-mechanical treatment for reducing the wear rate of CuCrZr tool electrodes during electro-discharge machining. Materials, 16(20), 2023: 6787. https://doi.org/10.3390/ma16206787
[13] X. Chen, P. Dong, Y. Zeng, H. Yao, J. Chen, Effect of heat treatment on the microstructure and properties of CuCrZr prepared by laser powder bed fusion. Materials Characterization, 214, 2024: 114103.
https://doi.org/10.1016/j.matchar.2024.114103
[14] A.M. Khorasani, M.R.S. Yazdi, M.S. Safizadeh, Analysis of machining parameters effects on surface roughness: A review. International Journal of Computational Materials Science and Surface Engineering, 5(1), 2012: 68–84. https://doi.org/10.1504/IJCMSSE.2012.049055
[15] N. Yusup, A.M. Zain, S.Z.M. Hashim, Evolutionary techniques in optimizing machining parameters: Review and recent applications (2007–2011). Expert Systems with Applications, 39(10), 2012: 9909–9927. https://doi.org/10.1016/j.eswa.2012.02.109
[16] H.A. Kishawy, A. Hosseini, Environmentally conscious machining. In: Machining Difficult-to-Cut Materials. Materials Forming, Machining and Tribology. Springer, Cham, 2019: 205–238.
https://doi.org/10.1007/978-3-319-95966-5_7
[17] H. Xie, X. Tang, F. Sun, R. Zhao, G. Li, C. Zhang, G. Huang, S. Fu, B. Peng, L. Dong, H. Chu, H. Zhou, X. Chen, P. Liu, Tensile and thermal properties, and microstructural evolution of additive-manufactured CuCrZr alloy at elevated temperature. Journal of Materials Research and Technology, 39, 2025: 5468–5479.
https://doi.org/10.1016/j.jmrt.2025.10.172
[18] S.R. Mundla, S. Arungalai Vendan, C.P. Paul, A.K. Shettigar, C. Jambagi, Experimental investigations on the milling characteristics of Cu alloys and additively manufactured CuCrZr. Materials Physics and Mechanics, 53(4), 2025: 1–21. https://doi.org/10.18149/MPM.5342025_1
[19] W.M. Li, Experimental study on cutting speed and surface roughness of pure copper in WEDM. Journal of Physics: Conference Series, 1605, 2020: 012054. https://doi.org/10.1088/1742-6596/1605/1/012054
[20] P. Niu, Q. Cheng, W. Chang, X. Song, Y. Li, Sensitivity analysis of machining accuracy reliability considering partial correlation of geometric errors for horizontal machining center. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 235(3), 2021: 455–465. https://doi.org/10.1177/0954405420958843
[21] G.C. Ganesha, S. Arungalai Vendan, M. Chaturvedi, S.T. Chandra, Parametric analysis using Pearson heat map on ultrasonic welding of PMMA polymer deployed for structural applications. 2025 3rd International Conference on Intelligent Cyber Physical Systems and Internet of Things (ICoICI), 17–19 September 2025, Coimbatore, India, pp.628–632. https://doi.org/10.1109/icoici65217.2025.11253698
[22] S. Radder, M. Chaturvedi, S.A. Vendan, Comprehensive weldability analysis and morphological-thermal insights into ultrasonic welding of ABS for electronics applications. Applied Engineering Letters, 10(3), 2025: 125–135. https://doi.org/10.46793/aeletters.2025.10.3.1
[23] R. Zhang, J. Fang, Y. Guo, H. Li, L. Shi, P. Liu, Effect of direct aging heat treatment on microstructures and properties of CuCrZr alloy manufactured by laser powder bed fusion. Journal of Materials Research and Technology, 36, 2025: 8591–8601. https://doi.org/10.1016/j.jmrt.2025.05.089
© 2026 by the authors. This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0)
Volume 11
Number 3
September 2026
Last Edition
Volume 11
Number 3
September 2026
How to Cite
S. Reddy Mundla, A.V. Subbiah, C.P. Paul, A.K. Shettigar, S.C. Jambagi, Tensile Properties, Micro-computed Tomography Defect Analysis, and Milling Performance of As-Built and Heat-Treated CuCrZr Parts Fabricated by Laser Powder Bed Fusion. Applied Engineering Letters, 11(3), 2026: 168-181.
https://doi.org/10.46793/aeletters.2026.11.3.5
More Citation Formats
Reddy Mundla, S., Subbiah, A.V., Paul, C.P., Shettigar, A.K., & Jambagi, S.C. (2026). Tensile Properties, Micro-computed Tomography Defect Analysis, and Milling Performance of As-Built and Heat-Treated CuCrZr Parts Fabricated by Laser Powder Bed Fusion. Applied Engineering Letters, 11(3), 168-181. https://doi.org/10.46793/aeletters.2026.11.3.5
Reddy Mundla, Subba, et al. “Tensile Properties, Micro-computed Tomography Defect Analysis, and Milling Performance of As-Built and Heat-Treated CuCrZr Parts Fabricated by Laser Powder Bed Fusion.“ Applied Engineering Letters, vol. 11, no. 3, 2026, 168-181. https://doi.org/10.46793/aeletters.2026.11.3.5
Reddy Mundla, Subba, Arungalai Vendan Subbiah, C. P. Paul, Arun Kumar Shettigar, and Sudhakar C. Jambagi. 2026. “Tensile Properties, Micro-computed Tomography Defect Analysis, and Milling Performance of As-Built and Heat-Treated CuCrZr Parts Fabricated by Laser Powder Bed Fusion.“ Applied Engineering Letters, 11 (3): 168-181. https://doi.org/10.46793/aeletters.2026.11.3.5
Reddy Mundla, S., Subbiah, A.V., Paul, C.P., Shettigar, A.K., and Jambagi, S.C. (2026). Tensile Properties, Micro-computed Tomography Defect Analysis, and Milling Performance of As-Built and Heat-Treated CuCrZr Parts Fabricated by Laser Powder Bed Fusion. Applied Engineering Letters, 11(3), pp. 168-181.
doi: 10.46793/aeletters.2026.11.3.5