ISSN 2466-4677; e-ISSN 2466-4847
Journal Menu
Archive
Last Edition
Archive
The Role of Solutionizing Treatment on Microstructure, Mechanical and Corrosion Properties of AZ91 Magnesium Alloy
Authors:
Rajasekhara Babu Kankanala1
, Arun Kumar Lakshmi Narayanan1
,
Ratna Sunil Buradagunta2
1Department of Manufacturing Engineering, Annamalai University, Chidambaram 608002, India
2Department of Mechanical Engineering, Bapatla Engineering College, Bapatla 522101, India
Received: 1 February 2026
Revised: 7 July 2026
Accepted: 3 August 2026
Published: 23 September 2026
Abstract:
In this research, AZ91 magnesium alloy was subjected to solutionizing at 410 °C for different soaking times (4, 8, 16, and 24 h), and the microstructure evolution, phase change, and mechanical and corrosion properties were investigated. From the microstructural studies, it was clearly observed that the intermetallic phase (Mg17Al12) appeared at the grain boundaries before heat treatment and was significantly altered after solutionizing. The X-ray diffraction studies after heat treatment clearly demonstrated a reduced fraction of intermetallic, which suggests the development of grains with super-saturated conditions due to the dissolved Al in the Mg lattice. Microhardness measurements showed decreased hardness (80.8 ± 2 HV0.1) with a lower level of variation within the measured values compared with the base alloy (93.6 ± 5.18 HV0.1). From the tensile test results, 8 h soaking time resulted in increased tensile strength up to 264.5 ± 6.1 MPa compared with the base alloy (171.6 ± 4.2 MPa) without sacrificing the % elongation. Further increasing the soaking time to 16 and 24 h did not improve the strength of the alloy. From the potentiodynamic polarization studies, lower corrosion current density values were observed for the samples with 8 and 16 h soaking time, which is attributed to the effect of lower intermetallic and homogeneous microstructure resulting from the heat treatment.
Keywords:
Heat treatment, Magnesium, Microstructure, Mechanical properties, Corrosion
References:
[1] J. Zhang, J. Miao, N. Balasubramani, D.H. Cho, T. Avey, C.-Y. Chang, A.A. Luo, Magnesium research and applications: Past, present and future. Journal of Magnesium and Alloys, 11(11), 2023: 3867-3895.
https://doi.org/10.1016/j.jma.2023.11.007
[2] R.L. Edgar, Global overview on demand and applications for magnesium alloys, In: Magnesium Alloys and their Applications, K.U. Kainer (ed.), Wiley-VCH, Germany, 2000: 1-8.
https://doi.org/10.1002/3527607552.ch1
[3] S. Jayasathyakawin, M. Ravichandran, N. Baskar, C. Anand Chairman, R. Balasundaram, Mechanical properties and applications of Magnesium alloy–Review. Materials Today: Proceedings, 27, 2020: 909-913. https://doi.org/10.1016/j.matpr.2020.01.255
[4] Y. Narukawa, K. Watanabe, K. Matsuda, T. Kawabata, S. Ikeno, Effect of Zn Contents on Microstructure in AZ-Series Magnesium Alloys. Advanced Materials Research, 409, 2011: 358–361.
https://doi.org/10.4028/www.scientific.net/AMR.409.358
[5] J. Ma, G. Wang, Y. Li, C. Qin, F. Ren, Electrochemical Investigations on AZ Series Magnesium Alloys as Anode Materials in a Sodium Chloride Solution. Journal of Materials Engineering and Performance, 28, 2019: 2873–2880. https://doi.org/10.1007/s11665-019-04035-w
[6] C. Ma, C. Hou, X. Zhang, T. Liu, N. Zhou, K. Zheng, Study on the microstructure and mechanical properties of Mg–Al–Li–Zn–Ti multi-component alloy. Journal of Materials Research and Technology, 29, 2024: 4781-4795. https://doi.org/10.1016/j.jmrt.2024.02.171
[7] C. Frank, W. Kasprzak, Heat Treatment of Magnesium Alloys – Current Capabilities. Materials Science Forum, 765, 2013: 466-470. https://doi.org/10.4028/www.scientific.net/MSF.765.466
[8] A. Pandya, M. Shah, B. Pramod, N. Srivastava, A Review on Heat Treatment of Magnesium Alloys and Its Effect on Various Properties. In: P.B. Pramod, U.B. Desai, S. Goel (Eds.), Advances in Material Science and Metallurgy. Lecture Notes in Mechanical Engineering, Springer, Singapore, 2023: 77-87.
https://doi.org/10.1007/978-981-19-4918-0_7
[9] G.G. Wang, J.P. Weiler, Recent developments in high-pressure die-cast magnesium alloys for automotive and future applications. Journal of Magnesium and Alloys, 11(1), 2023: 78-87.
https://doi.org/10.1016/j.jma.2022.10.001
[10] J. Tan, S. Ramakrishna, Applications of magnesium and its alloys: a review. Applied Sciences, 11(15), 2021: 6861. https://doi.org/10.3390/app11156861
[11] V.V. Ramalingam, P. Ramasamy, M.D. Kovukkal, G. Myilsamy, Research and development in magnesium alloys for industrial and biomedical applications: a review. Metals and Materials International, 26(4), 2020: 409-430. https://doi.org/10.1007/s12540-019-00346-8
[12] H. Xie, H. Zhao, X. Guo, Y. Li, H. Hu, J. Song, B. Jiang, F. Pan, Recent progress on cast magnesium alloy and components. Journal of Materials Science, 59, 2024: 9969-10002. https://doi.org/10.1007/s10853-024-09459-x
[13] B.C. Pai, U.T.S. Pillai, P. Manikandan, A. Srinivasan, Modification of AZ91 Mg alloys for high temperature applications. Transactions of the Indian Institute of Metals, 65, 2012: 601-606.
https://doi.org/10.1007/s12666-012-0166-1
[14] J. Iwaszko, M. Strzelecka, Microstructure and Corrosion Resistance of AZ91 Magnesium Alloy after Surface Remelting Treatment. Materials, 15(24), 2022: 8980. https://doi.org/10.3390/ma15248980
[15] G.E. Totten, Heat Treating of Nonferrous Alloys. ASM International, 4E, 2016: 640-649.
https://doi.org/10.31399/asm.hb.v04e.a0006254
[16] M. Şahbaz, S. Nalkıran, Microstructural refinement and mechanical property enhancement of AZ91 magnesium alloy via room-temperature multi-directional forging. Scientific Reports, 16, 2026: 9745.
https://doi.org/10.1038/s41598-026-42311-7
[17] C. Dong, L.-H. Pang, Y. Li, C. Xu, Effect of offset distance on the microstructure and properties of AZ91 magnesium alloy sheets processed by snake rolling. Materials Letters, 410, 2026: 140285.
https://doi.org/10.1016/j.matlet.2026.140285
[18] C. Chen, Y. Xu, H. Zhang, M. Zhang, J. Jia, J. Li, S. Chen, F. Wang, Grain refinement and β phase dispersion of AZ91D magnesium alloy by accumulative back extrusion: microstructure and mechanical properties. Journal of Materials Research and Technology, 37, 2025: 4176-4188.
https://doi.org/10.1016/j.jmrt.2025.07.112
[19] K. Wan, Q. Xu, Q. Hu, A. Wang, K. Hu, Y. Li, D. Yang, A. Ma, J. Jiang, Synergistic optimization of corrosion resistance in AZ91 alloy by lanthanum microalloying and equal-channel angular pressing. Journal of Rare Earths, 2026. (In Press). https://doi.org/10.1016/j.jre.2026.03.023
[20] G.V.V. Surya Kiran, K. Hari Krishna, S. Sameer, M. Bhargavi, B.S. Kumar, G. Mohana Rao, Y. Naidubabu, R. Dumpala, B.R. Sunil, Machining characteristics of fine grained AZ91 Mg alloy processed by friction stir processing. Transactions of Nonferrous Metals Society of China, 27(4), 2017: 804-811.
https://doi.org/10.1016/S1003-6326(17)60092-X
[21] F. Yousefpour, R. Jamaati, H. J. Aval, Effect of traverse and rotational speeds on microstructure, texture, and mechanical properties of friction stir processed AZ91 alloy. Materials Characterization, 178, 2021: 111235. https://doi.org/10.1016/j.matchar.2021.111235
[22] B.M. Hasani, H. Hedaiatmofidi, A. Zarebidaki, Effect of friction stir process on the microstructure and corrosion behavior of AZ91 Mg alloy. Materials Chemistry and Physics, 267, 2021: 124672.
https://doi.org/10.1016/j.matchemphys.2021.124672
[23] J. Iwaszko, K. Kudła, Microstructure, hardness, and wear resistance of AZ91 magnesium alloy produced by friction stir processing with air-cooling. The International Journal of Advanced Manufacturing Technology, 116(3), 2021: 1309-1323. https://doi.org/10.1007/s00170-021-07474-9
[24] K.J. Sandeep, A.K. Choudhary, R.J. Immanuel, Microstructural characterization and mechanical performance of AZ91 magnesium alloy processed by friction stir processing using novel tool designs. Journal of Materials Engineering and Performance, 33(1), 2024: 120-135. https://doi.org/10.1007/s11665-023-07980-9
[25] S.K. Baral, M.M. Thawre, B.R. Sunil, R. Dumpala, Synergetic Effect of Ball Burnishing and Friction Stir Processing on the Sliding Wear Behavior of ZE41 Magnesium Alloy. Journal of Materials Engineering and Performance, 35(4), 2026: 3978-3988. https://doi.org/10.1007/s11665-025-11855-6
[26] Y. Guo, G. Quan, M. Celikin, L. Ren, Y. Zhan, L. Fan, H. Pan, Effect of heat treatment on the microstructure and mechanical properties of AZ80M magnesium alloy fabricated by wire arc additive manufacturing. Journal of Magnesium and Alloys, 10(7), 2022: 1930-1940.
https://doi.org/10.1016/j.jma.2021.04.006
[27] A.K. Alfozan, Effect of Heat Treatment on Formability of AZ61 Magnesium Alloys. Solid State Phenomena, 356, 2024: 15-20. https://doi.org/10.4028/p-Bw1228
[28] R.S. Buradagunta, Synergic effect of grain refinement and solutionizing on mechanical properties and corrosion behavior of ZE41 Mg alloy aimed for biomedical applications. Materials Research Express, 13(1), 2026: 015401. https://doi.org/10.1088/2053-1591/ae30d3
[29] N. Najm, A.H. Ataiwi, R.A. Anaee, Annealing and Coating Influence on the Mechanical Properties, Microstructure, and Corrosion Properties of Biodegradable Mg Alloy (AZ91). Journal of Bio- and Tribo-Corrosion, 8, 2022: 64 https://doi.org/10.1007/s40735-022-00662-4
[30] N. Najm, A. H. Ataiwi, R. A. Anaee, Effect of indium coating on corrosion behavior of AZ31 Mg alloy by DC Sputtering. Materials Today: Proceedings, 62, 2022: 4551–4555.
https://doi.org/10.1016/j.matpr.2022.05.241
[31] N. Najm, A.H. Ataiwi, R.A. Anaee, R.S.A. Adnan, The effect of solid solution treatment with coating on corrosion properties of AZ91 Mg alloy in simulated body fluid. Materials Today: Proceedings, 2023. https://doi.org/10.1016/j.matpr.2023.10.009
[32] L. Cizek, M. Greger, L. Pawlica, L. A. Dobrzanski, T. Tanski, Study of selected properties of magnesium alloy AZ91 after heat treatment and forming. Journal of Materials Processing Technology, 157-158, 2004: 466–471. https://doi.org/10.1016/j.jmatprotec.2004.07.149
[33] M. Fatmi, A. Djemli, A. Ouali, T. Chihi, M.A. Ghebouli, H. Belhouchet, Heat treatment and kinetics of precipitation of β-Mg17Al12 phase in AZ91 alloy. Results in Physics, 10, 2018: 693-698.
https://doi.org/10.1016/j.rinp.2018.07.009
[34] V.S. Chowdary, R. Dumpala, S. Anand Kumar, V. V. Kondaiah, B. Ratna Sunil, Influence of heat treatment on the machinability and corrosion behavior of AZ91 Mg alloy. Journal of Magnesium and Alloys, 6(1), 2018: 52-58. https://doi.org/10.1016/j.jma.2017.12.001
[35] Z. Huang, Y. Pei, R. Huang, X. Gao, J. Zou, L. Jiang, Effect of Solution-treated on Electrochemical Properties of AZ91 Magnesium Alloy Anode. Journal of Electrochemical Science and Technology, 13(4), 2022: 486-496. https://doi.org/10.33961/jecst.2022.00430
[36] S. Prem Kumar, S. Kumaran, T. Srinivasa Rao, Structure – property correlation of precipitation hardened AZ91 magnesium alloy. Materials Science and Technology, 20(7), 2004: 835-838.
https://doi.org/10.1179/026708304225017256
[37] A. Srinivas, D. Pavan, B.K. Venkatesha, R. Raghavendra Rao, L. Mohith, Study on mechanical properties of AZ91 magnesium alloy. Materials Today: Proceedings, 54, 2022: 291-294.
https://doi.org/10.1016/j.matpr.2021.09.171
[38] SAE International Material Specification, Heat Treatment of Magnesium Alloy Castings. SAE Standard AMS2768C, USA, 2005. https://doi.org/10.4271/AMS2768C
[39] B.L. Mordike, T. Ebert, Magnesium: Properties – applications — potential. Materials Science and Engineering: A, 302(1), 2001: 37-45. https://doi.org/10.1016/S0921-5093(00)01351-4
[40] Z.-y. You, A.-x. Jiang, Z.-z. Duan, G.-p. Qiao, J.-l. Gao, L.-b. Guo, Effect of heat treatment on microstructure and properties of semi-solid squeeze casting AZ91D. China Foundry, 17, 2020: 219–226. https://doi.org/10.1007/s41230-020-9103-9
[41] R. Sarvesha, D. Chalapathi, M. Yadava, J. Jain, S.S. Singh, In-situ studies on deformation and fracture characteristics of AZ91 Mg alloy. Materialia, 18, 2021: 101177. https://doi.org/10.1016/j.mtla.2021.101177
[42] ASTM E8/E8M-22, Standard Test Methods for Tension Testing of Metallic Materials. ASTM International, West Conshohocken, PA, USA, 2022. https://doi.org/10.1520/E0008_E0008M-22
[43] ASTM E384-22, Standard Test Method for Microindentation Hardness of Materials. ASTM International, West Conshohocken, PA, USA, 2022. https://doi.org/10.1520/E0384-22
[44] F. Mansfeld, The polarization resistance technique for measuring corrosion currents, In: M.G. Fontana, R.W. Staehle, (Eds.). Advances in Corrosion Science and Technology. Springer, Boston, USA, 1976: 163-262. https://doi.org/10.1007/978-1-4684-8986-6_3
[45] M. Avedesian, H. Baker, ASM Specialty Handbook: Magnesium and Magnesium Alloys. ASM International, USA, 1999.
[46] Z.U. Rehman, J.S. Kim, D.G. Churchill, B.H. Koo, Tuning Corrosion Properties of the Bio-Inspired AZ-Series Mg Alloys Using Electrochemical Surface Treatment under Varying Experimental Regimes. Coatings, 12(11), 2022: 1617. https://doi.org/10.3390/coatings12111617
[47] S. Alomairy, Dissolution mechanism and kinetics of β(Mg17Al12) phases in AZ91 magnesium alloy. Journal of Magnesium and Alloys, 12(4), 2024: 1581-1592. https://doi.org/10.1016/j.jma.2024.03.020
[48] T. Zhu, Z. Chen, W. Gao, Dissolution of Eutectic β-Mg17Al12 Phase in Magnesium AZ91 Cast Alloy at Temperatures Close to Eutectic Temperature. Journal of Materials Engineering and Performance, 19, 2009: 860-867. https://doi.org/10.1007/s11665-009-9539-y
[49] B.R. Sunil, K.V. Ganesh, P. Pavan, G. Vadapalli, Ch. Swarnalatha, P. Swapna, P. Bindukumar, G.P.K. Reddy, Effect of aluminium content on machining characteristics of AZ31 and AZ91 magnesium alloys during drilling. Journal of Magnesium and Alloys, 4(1), 2016: 15-21. https://doi.org/10.1016/j.jma.2015.10.003
[50] P.-P. Wu, G.-L. Song, Y.-X. Zhu, Z.-L. Feng, D.-J. Zheng, The corrosion of Al-supersaturated Mg matrix and the galvanic effect of secondary phase nanoparticles. Corrosion Science, 184, 2021: 109410.
https://doi.org/10.1016/j.corsci.2021.109410
© 2026 by the authors. This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0)
Volume 11
Number 3
September 2026
Last Edition
Volume 11
Number 3
September 2026
How to Cite
R.B. Kankanala, A.K. Lakshmi Narayanan, R.S. Buradagunta, The Role of Solutionizing Treatment on Microstructure, Mechanical and Corrosion Properties of AZ91 Magnesium Alloy. Applied Engineering Letters, 11(3), 2026: 131-142.
https://doi.org/10.46793/aeletters.2026.11.3.2
More Citation Formats
Kankanala, R.B., Lakshmi Narayanan, A.K., & Buradagunta, R.S. (2026). The Role of Solutionizing Treatment on Microstructure, Mechanical and Corrosion Properties of AZ91 Magnesium Alloy. Applied Engineering Letters, 11(3), 131-142.
https://doi.org/10.46793/aeletters.2026.11.3.2
Kankanala, Rajasekhara Babu, et al. “The Role of Solutionizing Treatment on Microstructure, Mechanical and Corrosion Properties of AZ91 Magnesium Alloy.“ Applied Engineering Letters, vol. 11, no. 3, 2026, pp. 131-142.
https://doi.org/10.46793/aeletters.2026.11.3.2
Kankanala, Rajasekhara Babu, Arun Kumar Lakshmi Narayanan, and Ratna Sunil Buradagunta. 2026. “The Role of Solutionizing Treatment on Microstructure, Mechanical and Corrosion Properties of AZ91 Magnesium Alloy.“ Applied Engineering Letters, 11 (3): 131-142.
https://doi.org/10.46793/aeletters.2026.11.3.2
Kankanala, R.B., Lakshmi Narayanan, A.K., and Buradagunta, R.S. (2026). The Role of Solutionizing Treatment on Microstructure, Mechanical and Corrosion Properties of AZ91 Magnesium Alloy. Applied Engineering Letters, 11(3), pp. 131-142.
doi: 10.46793/aeletters.2026.11.3.2.