ISSN 2466-4677; e-ISSN 2466-4847
Journal Menu
Archive
Last Edition
Archive
The Effect of the Mixing Model on the Characteristics of Cu-Ni-Mo-4SiC Composite Synthesized by Powder Metallurgy
Authors:
Suprianto1
, Agnes Maysa Salsabila1
, Fadly Ahmad Kurniawan Nasution1
,
Ade Irwan1
, Irfan Sitorus2
, Bakhrul Ilmi2
1Department of Mechanical Engineering, Faculty of Engineering, Universitas Sumatera Utara, Jl. Almamater Kampus USU, Padang Bulan, Medan 20155, Indonesia
2Mechanical Engineering Graduate Study Program, Faculty of Engineering, Universitas Sumatera Utara, Jl. Almamater Kampus USU, Padang Bulan, Medan 20155, Indonesia
Received: 28 December 2025
Revised: 25 July 2026
Accepted: 7 August 2026
Published: 23 September 2026
Abstract:
The mixing method plays a decisive role in achieving microstructural uniformity and in defining the mechanical, tribological, and electrical performance of composite materials. This study aims to evaluate the characteristics of a Cu-Ni-Mo-4SiC composite produced using various powder mixing models. The composites were prepared through powder metallurgy employing horizontal mixing (HM), V-mixer blending (VM), and mechanical alloying (MA). The powders were mixed further, compacted at room temperature, and subsequently sintered at elevated temperatures. The resulting composites were examined using various characterization methods, including Scanning Electron Microscope (SEM) – Energy Dispersive Spectroscopy (EDS) for microstructural observation, X-ray Diffraction (XRD) for crystal structure identification, measurements of density, Vickers microhardness, wear resistance, and electrical conductivity at room temperature. The results show that mechanical alloying led to a finer crystallite size, a more homogeneous Cu-Ni matrix, better distribution of Mo and SiC particles, and reduced porosity. Hence, the highest performance was attained in the MA composite, which has a hardness of 65.1 HV, specific wear rate of 5.56 × 10-5 mm3/Nm, electrical conductivity of 62% IACS, and resistivity of 2.78 × 10⁻⁸ Ωm. This can be explained by finer grains, reduced particle aggregation, and even dispersion strengthening. As a result, under electrical service at room temperature and dry sliding load of 10 N for 20 min, the MA composite could serve as a material for electrodes and sliding electrical parts.
Keywords:
Mechanical alloying, Hardness, Homogeneity, Microstructure, Specific wear rate
References:
[1] M.R. Akbarpour, F. Gazani, H.M. Mirabad, I. Khezri, A. Moeini, N. Sohrabi, H.S. Kim, Recent advances in processing, and mechanical, thermal and electrical properties of Cu-SiC metal matrix composites prepared by powder metallurgy. Progress in Materials Science, 140, 2023: 101191.
https://doi.org/10.1016/j.pmatsci.2023.101191
[2] J. Feng, K. Song, S. Liang, X. Guo, S. Li, Mechanical properties and electrical conductivity of oriented-SiC-whisker-reinforced Al2O3/Cu composites. Journal of Materials Research and Technology, 20, 2022: 1470-1480. https://doi.org/10.1016/j.jmrt.2022.07.131
[3] M. Gao, R. Bao, J. Yi, C. Li, J. Tao, Y. Ren, L. Du, Y. Zhao, C. Wu, L. Liu, Simultaneously enhanced strength and wear-resistance of Ti3SiC2 MAX phase reinforced Cu-Ni-Si composite via powder metallurgy method. Journal of Alloys and Compounds, 1023, 2025: 180168. https://doi.org/10.1016/j.jallcom.2025.180168
[4] Z. Moser, W. Zakulski, P. Spencer, K. Hack, Thermodynamic investigations of solid Cu Ni and Fe Ni alloys and calculation of the solid state miscibility gap in the Cu Fe Ni system, Calphad, 9(3), 1985: 257-269.
https://doi.org/10.1016/0364-5916(85)90011-2
[5] T.D. Shen, C.C. Koch, Formation, solid-solution hardening and softening of nanocrystalline solid solutions prepared by mechanical attrition. Acta Materialia, 44(2), 1996: 753-761. https://doi.org/10.1016/1359-6454(95)00178-6
[6] C. Suryanarayana, Mechanical alloying and milling. Progress in Materials Science, 46(1–2), 2001: 1-184. https://doi.org/10.1016/S0079-6425(99)00010-9
[7] Z. Zhuang, Z. Li, L. Xu, Y. Feng, R. Wang, C. Peng, The influence of ball milling conditions on the powder characteristics and sintering densification of Mo-Cu alloy. International Journal of Refractory Metals and Hard Materials, 125, 2024: 106914. https://doi.org/10.1016/j.ijrmhm.2024.106914
[8] P. Cao, S. Liu, Y. Wu, Y. Xia, Z. Wu, Z. zhou, Y. Liu, A. Sun, Master sintering curve of binary mutually immiscible molybdenum-copper powders. Journal of Alloys and Compounds, 834, 2020: 155194.
https://doi.org/10.1016/j.jallcom.2020.155194
[9] Y. Liang, Q. Lei, X. Zhang, D. Jiang, Y. Li, Microstructure evolution and properties of a Cu-5 wt.% Mo alloy with high conductivity and high anti-soften temperature. Materials Today Communications, 32, 2022: 104134. https://doi.org/10.1016/j.mtcomm.2022.104134
[10] M. Chen, N. Luo, Z. Wang, Q. Liu, B. Wang, B. Niu, J. Yang, X. Wu, Q. Li, J. He, Surface modification of highly reflective Cu powder using Mo particles as modifiers for improving energy efficiency in laser additive manufacturing of Cu-Mo immiscible alloys. Journal of Manufacturing Processes, 136, 2025: 251-266.
https://doi.org/10.1016/j.jmapro.2025.01.069
[11] I. Cruz-Cruz, R. Hernández-Maya, J.E. Reséndiz-Hernández, O. Martínez-Romero, N.A. Ulloa Castillo, A. Elías-Zúñiga, Copper-Nickel/SiC composites for applications on contact electrodes. Heliyon, 10(22), 2024: e39965. https://doi.org/10.1016/j.heliyon.2024.e39965
[12] G.C. Efe, M. Ipek, S. Zeytin, C. Bindal, An investigation of the effect of SiC particle size on Cu-SiC composites. Composites Part B: Engineering, 43(4), 2012: 1813-1822.
https://doi.org/10.1016/j.compositesb.2012.01.006
[13] M. Moakher, T. Shinbrot, F.J. Muzzio, Experimentally validated computations of flow, mixing and segregation of non-cohesive grains in three-dimensional tumbling blenders. Powder Technology, 109(1-3), 2000: 58-71. https://doi.org/10.1016/S0032-5910(99)00227-2
[14] A. Alexander, F.J. Muzzio, T. Shinbrot, Segregation patterns in V-blenders. Chemical Engineering Science, 58(2), 2003: 487-496. https://doi.org/10.1016/S0009-2509(02)00530-4
[15] C. Yin, Z. Wang, J. Yuan, Influence of powder mixing processes and WC contents on microstructure, shrinkage behavior, and mechanical properties of WC–Si₃N₄ composites. Ceramics International, 49(16), 2023: 26747-26758. https://doi.org/10.1016/j.ceramint.2023.05.211
[16] S. Mahmood, A. Iqbal, Rafi-ud-Din, A. Wadood, A. Mateen, M. Amin, I.S. Yahia, H.Y. Zahran, Influence of homogenizing methodology on mechanical and tribological performance of powder-metallurgy-processed titanium composites reinforced by graphene nanoplatelets. Molecules, 27(9), 2022: 2666.
https://doi.org/10.3390/molecules27092666
[17] S.-J. Huang, Y.Y. Tanoto, C. Li, Effect of powder mixing on the mechanical strength of polyamide 6-AZ61 magnesium composites prepared by compression molding. Composites Communications, 53, 2025: 102169. https://doi.org/10.1016/j.coco.2024.102169
[18] A.M. Sankhla, K.M. Patel, M.A. Makhesana, K. Giasin, D.Y. Pimenov, S. Wojciechowski, N. Khanna, Effect of mixing method and particle size on hardness and compressive strength of aluminium-based metal matrix composite prepared through powder metallurgy route. Journal of Materials Research and Technology, 18, 2022: 282-292. https://doi.org/10.1016/j.jmrt.2022.02.094
[19] I. Dinaharan, T. Albert, Effect of reinforcement type on microstructural evolution and wear performance of copper matrix composites via powder metallurgy. Materials Today Communications, 34, 2023: 105250. https://doi.org/10.1016/j.mtcomm.2022.105250
[20] M.E. Cura, X.W. Liu, U. Kanerva, S. Varjus, A. Kivioja, O. Söderberg, S.P. Hannula, Friction behavior of alumina/molybdenum composites and formation of MoO₃₋ₓ phase at 400 °C. Tribology International, 87, 2015: 23-31. https://doi.org/10.1016/j.triboint.2015.02.010
[21] Q. Zhang, J. Wang, B.-Y. Zhang, B.-H. Guo, J. Yu, Z.-X. Guo, Improved electrical conductivity of polymer/carbon-black composites by simultaneous dispersion and interaction-induced network assembly. Composites Science and Technology, 179, 2019: 106-114. https://doi.org/10.1016/j.compscitech.2019.05.008
[22] B. Krause, P. Pötschke, L. Häußler, Influence of small scale melt mixing conditions on electrical resistivity of carbon-nanotube-polyamide composites. Composites Science and Technology, 69(10), 2009: 1505-1515. https://doi.org/10.1016/j.compscitech.2008.07.007
[23] Z. Xiao, Y.-j. Ding, Z.-j. Wang, Y.-l. Jia, Y.-b. Jiang, S. Gong, Z. Li, Research and development of advanced copper matrix composites. Transactions of Nonferrous Metals Society of China, 34(12), 2024: 3789-3821. https://doi.org/10.1016/S1003-6326(24)66641-0
[24] A. Patra, R. Saxena, S.K. Karak, Combined effect of Ni and nano-Y2O3 addition on microstructure, mechanical and high temperature behavior of mechanically alloyed W-Mo. International Journal of Refractory Metals and Hard Materials, 60, 2016: 131-146. https://doi.org/10.1016/j.ijrmhm.2016.07.017
[25] C. Suryanarayana, Mechanical Alloying: A Novel Technique to Synthesize Advanced Materials. Research, 2019, 2019: 4219812. https://doi.org/10.34133/2019/4219812
[26] S. Gaona-Jimenez, R.A. Rodriguez-Diaz, A. Sedano, J. Porcayo-Calderon, A.M. Ocampo, S. Serna-Barquera, J.O. Olarte-Cortes, J.A. Juarez-Islas, Synthesis of a nanostructured Al–Cu powder alloy with additions of TiC particles by mechanical alloying and ball milling–mathematical modelling of microstructure. Digest Journal of Nanomaterials and Biostructures, 12(2), 2017: 449-462.
[27] B. Zhang, R. Zhao, B. Ren, A. Jiang, C. Chen, J. Liu, Y. Zhou, Mechanical Alloying Behavior and Thermal Stability of CoCrCuFeMnNix High-Entropy Alloy Powders Prepared via MA. Materials, 16(8), 2023: 3179. https://doi.org/10.3390/ma16083179
[28] C. Shuai, C. He, S. Peng, F. Qi, G. Wang, A. Min, W. Yang, W. Wang, Mechanical alloying of immiscible metallic systems: process, microstructure and mechanism. Advanced Engineering Materials, 23, 2021: 2001098. https://doi.org/10.1002/adem.202001098
[29] Y. Yu, W. Xiao, J. Wang, L. Wang, First-principles study of Mo segregation in MoNi(111): Effects of chemisorbed atomic oxygen. Materials, 9(1), 2016: 5. https://doi.org/10.3390/ma9010005
[30] C. Shu, K. Chen, H. Yang, M. Chen, X. He, Effect of V and ball milling time on microstructure and thermal properties of CoCrCuFeNiVₓ by mechanical alloying. Physica B: Condensed Matter, 571, 2019: 235-242. https://doi.org/10.1016/j.physb.2019.07.028
[31] H. Toda, T. Inamori, K. Horikawa, K. Uesugi, A. Takeuchi, Y. Suzuki, M. Kobayashi, Effects of hydrogen micropores on mechanical properties in A2024 aluminum alloys. Materials Transactions, 54(12), 2013: 2195-2201. https://doi.org/10.2320/matertrans.L-M2013832
[32] H.-W. Hwang, J.-H. Park, D.-G. Lee, Effect of molybdenum content on microstructure and mechanical properties of Ti–Mo–Fe alloys by powder metallurgy. Applied Sciences, 12(14), 2022: 7257.
https://doi.org/10.3390/app12147257
[33] S. Hao, J. Li, K. Yamanaka, A. Chiba, Molybdenum segregation at grain boundaries in a nanograined Ni–Mo alloy: implications for yielding behavior and plastic deformation modes. Computational Materials Science, 256, 2025: 113973. https://doi.org/10.1016/j.commatsci.2025.113973
[34] W. Abd-Elaziem, A. Hamada, T. Allam, M.M. Mohammed, M. Abd-El Hamid, S. Samah, D. Wasfy, M. A. Darwish, Y.O.A.E. El-Kady, S. Elkatatny, Enhancement of mechanical and physical properties of Cu–Ni composites by various contents of Y₂O₃ reinforcement. Journal of Materials Research and Technology, 30, 2024: 473-484. https://doi.org/10.1016/j.jmrt.2024.03.075
[35] N.T. Câmara, R.A. Raimundo, C.S. Lourenco, L.M.F. Morais, D.D.S. Silva, R.M. Gomes, M.A. Morales, D.A. Macedo, U.U. Gomes, F.A. Costa, Impact of the SiC addition on the morphological, structural and mechanical properties of Cu–SiC composite powders prepared by high energy milling. Advanced Powder Technology, 32(8), 2021: 2950-2961. https://doi.org/10.1016/j.apt.2021.06.006
[36] M.M.J. Sridhar, M. Ravichandran, G. Veerappan, Microstructure and properties of silicon carbide and yttrium oxide reinforced copper matrix hybrid composites (Cu–SiC–Y₂O₃). Materials Research, 28, 2024: 1-11. https://doi.org/10.1590/1980-5373-mr-2024-0406
[37] M.I. Abd El Aal, Wear properties of copper and copper composites powders consolidated by high-pressure torsion. Friction, 8(2), 2020: 433-450. https://doi.org/10.1007/s40544-019-0285-3
[38] E. Şap, Investigation of mechanical properties of Cu/Mo–SiCp composites produced with powder metallurgy and their wear behaviour using the Taguchi method. Ceramics International, 47(18), 2021: 25910-25920. https://doi.org/10.1016/j.ceramint.2021.05.322
[39] N. Vashishtha, S.G. Sapate, J.S. Gahlot, P. Bagde, Effect of tribo-oxidation on friction and wear behaviour of HVOF sprayed WC–10Co–4Cr coating. Tribology Letters, 66(56), 2018: 1-19.
https://doi.org/10.1007/s11249-018-1006-1
[40] Y. Jiang, L. Xiao, Z. Peng, M. Li, J. Li, X. Wang, G. Deng, J. Fang, Z. Cai, X. Zhao, S. Liu, Laser cladding of heterogeneous structured Cu–Cr–W–SiC coatings with balanced electrical conductivity and wear resistance. Materials & Design, 254, 2025: 114009. https://doi.org/10.1016/j.matdes.2025.114009
© 2026 by the authors. This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0)
Volume 11
Number 3
September 2026
Last Edition
Volume 11
Number 3
September 2026
How to Cite
Suprianto, A.M. Salsabila, F.A.K. Nasution, A. Irwan, I. Sitorus, B. Ilmi, The Effect of the Mixing Model on the Characteristics of Cu-Ni-Mo-4SiC Composite Synthesized by Powder Metallurgy. Applied Engineering Letters, 11(3), 2026: 117-130.
https://doi.org/10.46793/aeletters.2026.11.3.1
More Citation Formats
Suprianto, Salsabila, A.M., Nasution, F.A.K., Irwan, A., Sitorus, I., & Ilmi, B. (2026). The Effect of the Mixing Model on the Characteristics of Cu-Ni-Mo-4SiC Composite Synthesized by Powder Metallurgy. Applied Engineering Letters, 11(3), 117-130. https://doi.org/10.46793/aeletters.2026.11.3.1
Suprianto, et al. “The Effect of the Mixing Model on the Characteristics of Cu-Ni-Mo-4SiC Composite Synthesized by Powder Metallurgy“. Applied Engineering Letters, vol. 11, no. 3, 2026, pp. 117-130.
https://doi.org/10.46793/aeletters.2026.11.3.1
Suprianto, Agnes Maysa Salsabila, Fadly Ahmad Kurniawan Nasution, Ade Irwan, Irfan Sitorus, and Bakhrul Ilmi. 2026. “The Effect of the Mixing Model on the Characteristics of Cu-Ni-Mo-4SiC Composite Synthesized by Powder Metallurgy“. Applied Engineering Letters, 11 (3): 117-130.
https://doi.org/10.46793/aeletters.2026.11.3.1
Suprianto, Salsabila, A.M., Nasution, F.A.K., Irwan, A., Sitorus, I., and Ilmi, B. (2026). The Effect of the Mixing Model on the Characteristics of Cu-Ni-Mo-4SiC Composite Synthesized by Powder Metallurgy. Applied Engineering Letters, 11(3), pp. 117-130.
doi: 10.46793/aeletters.2026.11.3.1.